John Deere H160 Loader
Front End Loaders for Tractors
Your Preferred Location
Specifications
Key Specs - Boom breakout force: |
Measured at pivot (Y) 1295 kgf 2855 lbf Measured at 500 mm ahead of pivot (Z) 922 kgf 2032 lbf |
Key Specs - Bucket rollback force capacity: |
At ground-level line (ZZ) 1188 kgf 2619 lbf |
Key Specs - Clearance at full height - bucket dumped (C): |
1743 mm 68.6 in. |
Key Specs - Dump angle, degrees (E): |
43 degree (angle) |
Key Specs - Lift capacity at full height: |
Measured at pivot (U) 617 kgf 1360 lbf Measured at 500 mm ahead of pivot (V) 453 kgf 999 lbf |
Key Specs - Maximum lift height (A): |
2284 mm 90 in. |
Key Specs - Rollback angle, degrees (G): |
25 degree (angle) |
Loader - Base weight: |
257.21 kg |
Loader - Boom breakout force: |
Measured at pivot (Y) 1295 kgf 2855 lbf Measured at 500 mm ahead of pivot (Z) 922 kgf 2032 lbf |
Loader - Bucket angle: |
Dump angle, degrees (E) 43 degree (angle) Rollback angle, degrees (G) 25 degree (angle) |
Loader - Bucket rollback force capacity: |
At maximum height (VV) 1205 kgf 2657 lbf At 59-in. (1500-mm) lift height (XX) 1518 kgf 3347 lbf At ground-level line (ZZ) 1188 kgf 2619 lbf |
Loader - Bucket weight: |
93.8 kg 206.8 lb |
Loader - Cycle times: |
Loader raise, seconds 2.76 seconds Loader lower, seconds 1.69 seconds Bucket dump, seconds 2.91 seconds Bucket rollback, seconds 1.72 seconds |
Loader - Digging depth (H): |
76 mm 2.9 in. |
Loader - Dimensions: |
Maximum lift height (A) 2284 mm 90 in. At full height - bucket level(B) 83.5 in. 2123 mm At full height - bucket dumped (C) 1743 mm 68.6 in. |
Loader - Lift capacity at 59 in. (1500 mm): |
Measured at pivot (W) 771 kgf 1700 lbf Measured at 500 mm ahead of pivot (X) 595 kgf 1312 lbf |
Loader - Lift capacity at full height: |
Measured at pivot (U) 617 kgf 1360 lbf Measured at 500 mm ahead of pivot (V) 453 kgf 999 lbf |
Loader - Overall length (I+F), ft (m): |
3.122 m 10.24 ft |
Loader - Reach: |
At maximum height (D) 773 mm 30.4 in. At ground level - bucket level (F) 1381 mm 54.4 in. |
Tractor - Front tire: |
7.00-14 6PR R1 |
Tractor - Model: |
3120/3320/3520/3720 |
Tractor - Pump capacity: |
8.6 gpm |
Tractor - Rated pressure: |
2500 psi |
Tractor - Rear tire: |
11.2-24 6PR R1 |
Tractor - Wheelbase: |
1727 mm 68 in. |
End-of-pin lubrication means easy maintenance
Close up of grease fitting
Pivot point grease fitting locations
All pivot points on the loader have grease fittings that are accessible from the side of the loader to make greasing the loader much easier, ensuring that all grease points are more likely to be serviced. No more searching for grease points that are hard to find. Removing the grease gun from the grease fitting or zerk is not a problem either as sufficient radius has been left to allow the grease gun tip to be rotated to the side for removal from the fitting or zerk.
Quik-Park™ loader mounting system
Quik-Park loader mounting system
The H-Series Loaders are designed for easy removal and mounting to and from the tractor without tools.
The parking stand, attached to the front frame of the tractor, is an integral part of the loader during loader operation.
The parking stand lowers into position by moving the joystick to the raised position once the latches are opened. This allows the loader to move to the parked position.
To view a video of how the Quik-Park™ system works click here.
NOTE: This video only shows the dismount and mount of the loader without disconnecting the hydraulics. To completely remove the loader, the operator must turn the tractor off, relieve the hydraulics, and then disconnect the hoses from the couplers.