John Deere 536D Draper
Windrowers
Your Preferred Location
Specifications
Auxiliary top auger - Type: |
Optional: factory-installed cross-pea auger |
Cutterbar - Cut width (length): |
11 m 36 ft |
Cutterbar - Cutterbar tilt: |
Hydraulic, adjustable from cab |
Cutterbar - Knife drive: |
Two hydraulic motors and two knife drives |
Cutterbar - Knife speed: |
1,100 to 1,440 spm |
Cutterbar - Stroke length: |
84 mm 3.3 in. |
Cutterbar - Type: |
SCH® Easy Cut with roller guides, spring steep guards, and bolted sections Standard: dual knife |
Dimensions - Operating width (field): |
11 m 36 ft |
Dimensions - Transport height: |
2.44 m 8 ft |
Dimensions - Transport length, hitch extended: |
12.5 m 40.8 ft |
Dimensions - Transport width (reel fully retracted): |
2.6 m 8.5 ft |
Draper and decks - Belt width: |
V-guided draper belt: 106.7 cm 42 in. |
Draper and decks - Deck extensions: |
Optional, dealer-installed deck extensions: 35.6 cm 14 in. |
Draper and decks - Deck tilt: |
Standard |
Draper and decks - Delivery opening height: |
205.7 cm 81 in. |
Draper and decks - Delivery opening width: |
Delivery, double swath opening: 137.2 cm 54 in. Delivery, single swath opening: 203.2 cm 80 in. |
Draper and decks - Draper drive: |
Two hydraulic motors |
Draper and decks - Operating speed: |
0 to 232 m/min 0 to 760 fpm |
Draper and decks - Remote canvas speed control: |
Standard |
Draper and decks - Speed control: |
Adjustable in windrower cab |
Gauge wheels and transportation - Gauge wheels: |
Adjustable castoring gauge wheel optional |
Gauge wheels and transportation - Integrated slow speed transport system: |
Self-contained transport, including hitch, jack and axle, is conveniently stored on the swather table |
Key Specs - Belt width: |
V-guided draper belt: 106.7 cm 42 in. |
Key Specs - Cut width (length): |
11 m 36 ft |
Key Specs - Cutterbar - Type: |
SCH® Easy Cut with roller guides, spring steep guards, and bolted sections Standard: dual knife |
Key Specs - Fingers: |
Plastic |
Key Specs - Reel type: |
Hydraulic |
Key Specs - Transport length, hitch extended: |
12.5 m 40.8 ft |
Reel - Diameter: |
1118 mm 44 in. |
Reel - Fingers: |
Plastic |
Reel - Height control: |
Hydraulic, adjustable from cab |
Reel - Number of bats: |
Six |
Reel - Reel fore and aft: |
Hydraulic, adjustable from cab |
Reel - Reel lift: |
Hydraulic, adjustable from cab |
Reel - Reel type: |
Hydraulic |
Reel - Speed control: |
Hydro handle, in cab |
Weight - Approximate weight (base platform with reel): |
3207 kg 7070 lb |
Weight - Approximate weight (base platform without reel): |
1458 kg 4852 lb |
Interchangeable with John Deere rotary platforms
500D Draper and interchangeable rotary platform
500D Draper has an interchangeable rotary platform:
- Interchangeable on W235 or W260 traction units in 30 minutes or less
- Growers can use one traction unit for harvesting both small grains and hay
Higher productivity with center-driven belts
Center-driven belts
500D Draper on W235 Windrower
- Deliver increased torque
- Enable greater productivity with minimal belt slippage
- Increase performance in heavy crop conditions
Red circles point out the location of the belt drive motors
- Draper belts on the 500D are driven from the center of the platform
- Delivers increased belt performance compared to drapers with end-driven belts
Belt drive motors
Motor driving the left-hand belt
Motor driving the right-hand belt
Due to the motors pulling the belt (instead of pushing in an end drive system), there is less slack in the belt. This delivers an increase in belt torque.
As a result, producers will experience minimal belt slippage and increased performance in heavy crop conditions due to the center-driven belt system.
John Deere parts and service support provide uptime for a timely harvest
Sales, parts, and service support from a local John Deere dealer offer overnight parts delivery and a well-trained support staff.
Draper hydraulic pump control logic delivers constant header speed
500D Draper on windrower
The draper hydraulic pump control maintains knife, belt, and reel speeds regardless of engine rpm changes.
- Results in uniform cut quality and windrow formation regardless of the terrain or engine load
- Reduces crop loss or shatter
Strong, positive-feeding reel handles all crop conditions
500D Draper
The 500D Series includes an improved reel that increases durability in heavy crop conditions.
500D Draper teeth
- Easy reel tooth replacement is done with a 90-degree turn with a wrench. It will allow the reel tooth to be removed and replaced.
- Additional teeth can be added at any location along the extruded tooth bar.
Hydraulic deck shift (double swath package)
John Deere 525D, 530D, and 536D Drapers can windrow out of the center, right, or left ends of the draper with the press of a button using the hydraulic shift option (double swath package).
- Larger windrows to match combine or self-propelled forage harvester
- Match narrower-width drapers with higher-capacity harvesting
- Place higher-density windrows in front of harvesters when yields are low
- Discharge two windrows side by side for uniform combine or forage harvester feeding
First pass with right discharge
Second pass with right discharge
Third pass with left discharge
Center discharge