Description

Models

Put more power to the ground, more comfortably, with the industry-exclusive HydraCushion™ suspension

Power that doesn’t get to the ground is power that’s being wasted. And a bumpy, hoppy ride can quickly drain an operator’s energy and productivity. So to help you get the most from every horse under the hood and every hour in the cab, 9R Tractors in wheeled configurations are available with the advanced, industry-exclusive HydraCushion suspension (HydraCushion is standard equipment on 477-kW [640-hp] models).

Along with a proven-reliable suspension design, HydraCushion suspension uses an advanced system of electronic sensors and hydraulic components to keep the chassis and front differential vertically centered, giving you more consistent contact with the ground while reducing road lope and smoothing out the bumps that cause a rough, tiring ride.

A range of hydraulic options give you the power and flexibility to take on your toughest applications

Of course, the 9 Series has the hydraulic muscle you need to push, pull, lift, and power your most demanding implements. But thanks to a range of enhancements to the hydraulic system, these tractors can provide that power at lower engine speeds, saving you fuel while still giving your implements the capacity they need. Regardless of model or configuration, the new 9 Series hydraulic system gives you:

• An increase of almost 40 percent in charge pump capacity, from 54-cc to 75-cc, to help maintain a higher flow at lower engine speeds
• A new swash plate angle sensor to monitor hydraulic flow and pressure and adjust engine speed to meet demand
• An integrated hydraulic pump, filter, and priority valve for fewer and shorter lines, reduced pressure loss, fewer flow restrictions, and an extra level of reliability

And if you depend on implements that need continuous hydraulic power, the 9 Series Tractors are available with Intelligent Power Management (IPM). Using dual pumps and advanced sensor and control technology, IPM provides additional engine and hydraulic power for high-demand applications like air seeding up and over hills or through thick, tough soil.

Add in single and dual pump options and a flexible number rear SCVs, and you can configure a powerful, fuel-efficient hydraulic system to meet the demands of your specific operation without paying for capacity you don’t need.

In the field or on the road: adjust steering ratio on-the-go with ActiveCommand Steering (ACS™)

You don’t have to compromise between pinpoint turns in the field and smooth, easy steering during transport – you can have it all with ActiveCommand Steering (ACS), available on all 9R and 9RX Tractors.

ACS lets you choose your steering ratio based on the task at hand. For precise headland maneuvers in the field, choose a tight 3.5 turns lock-to-lock. When you’re done in the field, ACS gives you a full five turns for smoother line-holding during road transport. Variable-effort resistance automatically changes with ground speed; you’ll notice a lighter touch during low-speed, in-field turns, and increased feedback at transport speeds for more comfortable, confident steering over the road. Plus, ACS works seamlessly with AutoTrac™ guidance systems and is compatible with wide and narrow section width tires as well as wide and narrow belts on 9RX models.

The end result? Reduced overall steering effort and fatigue, no drift and no backlash through the hand-wheel, all with the “connected” feel of a traditional steering column system

9 Series Visibility packages let you run with confidence, dawn until dusk

Visibility is more than just lighting. It’s mirrors where you need them, shades for the blinding late-fall and early-spring sun, wipers to help keep all the glass clear, and integrated camera capability. The new 9 Series Tractors let you choose the visibility package that best suits your needs – Select, Premium, or Ultimate with 360-degree light-emitting diode (LED) lighting –so you and your operators can run with all-conditions confidence.

 

	Select	Premium	Ultimate
Lighting	18 halogen worklights	18 LED worklights	24 LED worklights and eight LED convenience lights*
Mirrors	Mechanical	Electric and heated	Electric, heated, and telescoping
Sunshades	Front	Front, right-hand side, and rear	Front, right-hand side, and rear
Wipers	Front and rear	Front, right-hand side, and rear	Front, right-hand side, and rear
Cameras	Camera ready	Camera ready	Camera ready**

*Convenience lights illuminate the corners of the cab for easier entry and exit.

** Starting with model year 2022, the Ultimate visibility package will be camera ready.

Work at your best with 9 Series Comfort and Convenience packages

When you’re spending dozens of hours per week in the cab, a comfortable operating environment isn’t just an option – the right features, in the right places, let you and your operators work at your best, dawn to dusk and beyond.

The 7, 8, and 9 Series Tractors offer three Comfort and Convenience packages to fit your needs: Select, Premium, and Ultimate. But regardless of which package you choose, you’ll still get the John Deere CommandARM™ console that puts critical controls within easy reach. You’ll get all the storage space you need for drinks, meals, and other stowable items. And you’ll have plenty of outlets to keep your electronics powered.

 

Comfort and Convenience packages	Select	Premium	Ultimate
Seat	Cloth Mechanical controls Mechanical lumbar 8-degree left-hand and 40-degree right-hand swivel	Cloth Electronic controls Pneumatic lumbar 25-degrees left-hand and 40-degree right-hand swivel	Leather Electronic controls Pneumatic lumbar 25-degree left-hand and 40-degree right-hand swivel Heated/ventilated Massage Adjustable bolsters
Infotainment	AM/FM Auxiliary and Bluetooth® wireless inputs Four speakers	16.5-cm (6.5-in.) touchscreen radio, XM® ready Six speakers with subwoofer	16.5-cm (6.5-in.) touchscreen radio, XM ready Six speakers with subwoofer
Business band ready	X	X	X
Four USB and one 12-V outlet	X	X	X
Dual tilt column	X	X	X
Footrests	---	X	X
Refrigerator	---	X	X
120-V/300-W three-prong outlet	---	X	X
Carpeted floor mat	---	---	X
Leather-wrapped steering wheel	---	---	X

 

Bluetooth is a trademark of Bluetooth SIG, Inc. XM is a trademark of Sirius XM Radio Inc.

The new 9 Series: Easy to run, easy to maintain

When you’re trying to get a field planted before weather moves in, there’s no time to hit a scheduled maintenance interval or get smacked with an unexpected repair. That’s why we designed the 9 Series for maximum reliability and less in-season maintenance.

To start, we simplified as many systems as possible, using components common to other tractor lines and minimizing potential downtime due to parts availability. Then we eliminated as many potential pain points as possible through changes in the cooling, aftertreatment, and diagnostic systems, including:

• Replacing the fan drive system with a maintenance-free hydraulic fan drive
• Streamlining aftertreatment with a single-canister inline system that’s simpler and features fewer parts
• Improving uptime by adding better descriptions to diagnostic codes and offering predictive diagnostics through John Deere Expert Alerts
• A front-left service panel for easier access to engine oil check and fill points;
• Offering a 500-hour oil change interval on the John Deere Power Systems 13.6L (827-cu in.) Final Tier 4 (FT4) engine when using approved John Deere oil and filter (the Cummins® QSX 15-L [915-cu in.] engine has a 400-hour engine oil and filter change interval).

Cummins is a trademark of Cummins, Inc.

PowerTech™ 13.6L (827-cu in.) engine: real world usability, not just power on paper

The muscle to handle heavy draft disks and rippers, power-hungry air seeders and planters, and large transport loads like grain carts and slurry wagons. The durable design and heavy-duty components you can depend on when you need to get in and get out. All in a Final Tier 4 (FT4) and Stage V compliant package. You get real-world power with the purpose-built 13.6L (827-cu in.) engines from John Deere Power Systems, standard in the 291 to 440 engine kW (390 to 590 engine hp) 9 Series Tractors.

We developed our newest power plant from a clean sheet of paper, starting with stronger castings, beefier bearings, and more robust internal components, all designed to meet the high demands of field operations. We replaced the fuel injectors with a high-pressure common rail (HPCR) fuel system and eliminated the diesel particulate filter (DPF) to boost to fuel efficiency and lower operation and maintenance costs. Integrated coolant and oil passages, along with a new belt-driven water pump, eliminate potential leak points and allow for a less-crowded engine compartment, improving serviceability and reducing debris accumulation.

In redesigning the engine, we also gave it:

• Hydraulic valve lash adjusters to maintain valve-lash settings during engine operation, reduce valve train noise and wear, and allow for greater fuel efficiency.
• A hydraulic fan drive for improved cooling capacity with no required maintenance.
• A new integrated wiring harness design featuring a modular layout for reduced vibration, greater reliability, and easier service and diagnostics.
• A rear gear train that integrates fully into the cast-iron block, reducing tiresome engine noise and improving the durability of the crankshaft damper.
• Combination sensors where possible, meaning fewer sensors, connectors, and wires.
• A powerful engine brake that allows operators to use the engine to control tractor and implement speeds while transporting or traveling downhill, reducing wear on the drivetrain brake components.

It all adds up to:

• 14 percent more power and 11 percent more torque
• 3 percent lower fuel consumption
• 10 percent lighter
• 27 percent reduction in mean repair time and an estimated $8,308 savings in service costs over the life of the engine

13.5L (824-cu in.) engine compared to 13.6L (827-cu in.) engine

Feature	13.5L (824-cu in.) engine	13.6L (827-cu in.) engine
Fuel delivery	Electronic unit injectors (EUI)	HPCR
Aftertreatment	Two canisters	One canister
Valve lash adjustment	Manual	Automatic
Engine brake	Not available	Available above 402.7 kW (540 hp)
Wire harness	Single harness	Three short harnesses
Water pump	Gear driven	Belt driven
Gear train	Front mounted	Rear mounted
Fan drive	Vari-Cool™ system	Hydraulically driven

John Deere integrated solutions: a world of connected technology, right from the factory

John Deere makes it easy for you to access an entire suite of connected applications, all designed to help you make the most of every seed, every hour, every gallon, and every bit of machine-related information.

Each 9 Series Tractor comes standard with the John Deere StarFire™ 6000 Integrated Receiver and Generation 4 CommandCenter™ display; there’s no need for setup, installation, or initial global positioning system (GPS) calibration. Integrated AutoTrac™ assisted steering gives you accurate, scalable guidance for low-stress operation in nearly any conditions and can improve field efficiency by 10 percent or more. The 9 Series Tractors also feature standard JDLink™ telematics and users can turn on connectivity in the John Deere Operations Center for anytime, anywhere access to critical machine and field information. And every tractor comes from the factory with John Deere Connected Support™, so you and your dealer can anticipate and address critical system needs.

From here? The sky’s the limit. Choose any of our operation-specific applications to help maximize efficiency and productivity during planting, tillage, or other field activities.

 

*NOTE: Ordering is temporarily unavailable for the StarFire 6000 Integrated Receiver. John Deere is diligently working to resolve this issue. Please watch the Price Pages and the announcements in the Sales Manual for updates. We apologize for any inconvenience.

 

StarFire 6000 Integrated Receiver	AutoTrac	JDLink
Base equipment: Generation 4 CommandCenter display StarFire 6000 Integrated Receiver Optional equipment: Generation 4 CommandCenter display plus extended monitor	Base equipment: AutoTrac activation SF3 accuracy (+/- 3 cm [1.2 in.]) Data Sync Optional equipment: AutoTrac RowSense™ system* AutoTrac Turn Automation** AutoPath™ system** AutoTrac Implement Guidance* Gen 4 Machine Sync	Base equipment: JDLink telematics system Wireless Data Transfer John Deere Connected Support service Expert Alerts Remote Display Access Service ADVISOR™ Remote service tool

*Available with Premium Activation 3.0
**Available with Automation Activation 4.0

Specifications

• Additional information - Date collected: 1 March 2021
• Capacities - Cooling system: 56.5 L<br/>14.9 U.S. gal.
• Capacities - Crankcase oil volume: 64 L<br/>16.9 U.S. gal.
• Capacities - Diesel exhaust fluid (DEF) tank: 120 L<br/>31.7 U.S. gal.
• Capacities - Fuel tank: 1514 L<br/>400 U.S. gal.
• Capacities - Transmission-hydraulic system: With 3-point hitch and PTO: 227 L<br/>60 U.S. gal.<br/>Without 3-point hitch and PTO: 220 L<br/>58 U.S. gal.
• Dimensions - Approximate shipping weight, Open;Cab: 20,856 kg<br/>45,980 lb
• Dimensions - Drawbar clearance: Group 48 tires: 527 mm<br/>20.7 in.
• Dimensions - Overall length: With front weights, excluding hitch and coupler: 7945 mm<br/>312.8 in.<br/>With front weights, including hitch and coupler: 8427 mm<br/>331.8 in.
• Dimensions - Wheelbase: 3912 mm<br/>154 in.
• Drawbar - Drawbar category: Category 4 or Category 5
• Drawbar - Maximum vertical load: Standard: 2470 kg<br/>5450 lb<br/>Optional: Category 4 with heavy-duty drawbar support: 2470 kg<br/>Category 5 with heavy-duty drawbar support: 5440 kg<br/>12,000 lb
• Electrical system - Alternator size: Standard: 250 amp<br/>Optional: 330 amp
• Electrical system - Battery options: 12 V
• Electrical system - Total cold cranking amps: 3 x 925 CCA<br/>Total: 2775 CCA
• Electrical system - Type of bulb in headlight (Halogen, Zenon, LED): Standard: halogen, 65 W<br/>Optional: LED
• Electrical system - Working lights: Standard: 18 halogen<br/>Optional: 18 or 24 LED plus 8 LED conveninence lights
• Engine performance - Engine peak torque: At 1600 rpm: 1800 Nm 1328 lb-ft
• Engine performance - Maximum engine power: 316 kW<br/>429 hp
• Engine performance - Power boost: 10 percent
• Engine performance - PTO torque rise: 38 percent
• Engine performance - Rated power: 287 kW<br/>390 hp
• Engine performance - Rated PTO power (hp SAE): 249 kW<br/>335 hp
• Engine specifications - After treatment type: Diesel oxidation catalyst (DOC)/selective catalytic reduction (SCR)
• Engine specifications - Aspiration: Single wastegated turbocharger with air-to-air aftercooling and cooled exhaust gas recirculation (EGR)
• Engine specifications - Description: John Deere PowerTech 13.6L (B20 diesel compatible)
• Engine specifications - Displacement: 13.6 L<br/>827 cu in.
• Engine specifications - Emission level: Final Tier 4 (FT4)
• Engine specifications - Engine type: Diesel, inline, 6-cylinder, wet-sleeve cylinder liners with four valves in-head
• Engine specifications - Rated speed: 2100 rpm
• Front axle - Front axle differential lock: Full-locking electrohydraulic
• Front axle - Type: Diameter: 120 x 3048 mm<br/>4.72 x 120 in.
• Hydraulic system - Available flow at a single rear SCV: 1.3-cm (1/2-in.) couplers: 132 L/min<br/>35 gpm<br/>1.9-cm (3/4-in.) couplers: 159 L/min<br/>42 gpm
• Hydraulic system - Number of rear selective control valves (SCVs): Four to eight factory or field installed<br/>Base: four 1.3-cm (1/2-in.) couplers<br/>Optional: five to six 1.3-cm (1/2-in.) couplers factory installed<br/>Optional: three 1.9-cm (3/4-in.) couplers plus five 1.3-cm (1/2-in.) couplers factory installed
• Hydraulic system - Pump rated output: Standard: 208 L/min<br/>55 gpm<br/>Optional: 416 L/min<br/>110 gpm
• Hydraulic system - SCV control: Electronic
• Hydraulic system - Type: Closed-center, pressure-and-flow compensated
• Key Specs - Base machine weight: 20,856 kg<br/>45,980 lb
• Key Specs - Engine description: John Deere PowerTech™ 13.6L (B20 diesel compatible)
• Key Specs - Engine displacement: 13.6 L<br/>827 cu in.
• Key Specs - Hydraulic pump rated output: Standard: 208 L/min<br/>55 gpm<br/>Optional: 416 L/min<br/>110 gpm
• Key Specs - Maximum engine power: 316 kW<br/>429 hp
• Key Specs - Rated engine power: 287 kW<br/>390 hp
• Key Specs - Rated PTO power (hp SAE): 249 kW<br/>335 hp
• Key Specs - Rear hitch category (SAE designation): Category 4N: 6804 kg<br/>15,000 lb<br/>Category 4N: 9072 kg<br/>20,000 lb<br/>Category 4N/4: 6804 kg<br/>Category 4N/4: 9072 kg
• Key Specs - Transmission type: John Deere e18&trade; 18-speed PowerShift&trade; with Efficiency Manager&trade;: 40 km/h<br/>25 mph
• Miscellaneous - Country of manufacture: USA
• Operator station - Cab glass area: 6.64 m²<br/>71.47 sq ft
• Operator station - Display: Standard: Generation 4 4600 CommandCenter&trade;: 25.4 cm<br/>10 in.<br/>Optional: Extended monitor
• Operator station - Inner cab volume: 3.27 m³<br/>115 cu ft
• Operator station - Instructional seat: Standard
• Operator station - Radio: Standard: AM/FM stereo with weatherband, remote controls, auxiliary input jack, four speakers and external antenna<br/>Optional: Touchscreen radio
• Operator station - Seat: Degree of seat swivel, left hand<br/>25 degree (angle)<br/>Degree of seat swivel, right hand<br/>40 degree (angle)<br/>Standard: air suspension<br/>Optional: ActiveSeat&trade; II
• Precision AG - Guidance: Integrated AutoTrac&trade;
• Precision AG - Remote diagnostics: Available with activated JDLink hardware and activations
• Precision AG - Telematic: Available with JDLink&trade; hardware, activations, and Ethernet harnesses (availability dependent upon destination)
• Rear axle - Final drive type: Inboard planetary with double-reduction axle
• Rear axle - Rear differential lock: Full-locking electrohydraulic
• Rear axle - Type: Diameter: 120 x 3048 mm<br/>4.72 x 120 in.
• Rear hitch - Hitch category (SAE designation): Category 4N: 6804 kg<br/>15,000 lb<br/>Category 4N: 9072 kg<br/>20,000 lb<br/>Category 4N/4: 6804 kg<br/>Category 4N/4: 9072 kg
• Rear hitch - Maximum lift capacity behind lift points: Category 4N/4: 9072 kg<br/>20,000 lb
• Rear hitch - Sensing type: Electrohydraulic with draft sensing
• Rear power take-off (PTO) - PTO actuation: Electrohydraulic
• Rear power take-off (PTO) - Type: Independent<br/>44 mm (1.75 in.) 20-spline, 1000 rpm
• Serviceability - Interval for engine coolant change: 6000 hours
• Serviceability - Interval for engine oil change: 500 hours
• Serviceability - Interval for hydraulic/transmission oil change: 1500 hours
• Steering - Type: Standard: Hydraulic power steering<br/>Optional: ActiveCommand Steering (ACS&trade;)
• Tires - Turning radius with brakes: Group 47 or Group 48 tires: 6.035 m<br/>19.8 ft
• Transmission - Type: John Deere e18 18-speed PowerShift with Efficiency Manager: 40 km/h<br/>25 mph
• Weight - Base machine weight: 20,856 kg<br/>45,980 lb
• Weight - Maximum ballast level: 27,216 kg<br/>60,000 lb

Features

• Engine HP¹: Max: 429 hp (316 kW)
  Rated: 390 hp (287 kW)
• Track width and Tread Spacing: N/A
• Ride Comfort: ActiveSeat™II
  HydraCushion™
• PTO HP: Rated: 335 hp (249 kW)
• Transmission: e18™ PowerShift with Efficiency Manager
• Hydraulics: 55 or 110 gpm
  SCV 4-8 factory installed

Copy Set