John Deere 2630 Three- and Five-Section Tandem Disks
Description
- Perfect for light to medium soils, seedbed prep
- Features John Deere TruSet™ Tillage Technology
- Radial Tire Option
- Knife-edge Rolling Basket
- Extended-Life Bearing
Models
Mechanical wing control increases frame levelness for five-section disks
Spring pack
Spring pack
John Deere’s mechanical wing control helps producers keep their frames level for five-section disks. Mechanical wing control is included in base equipment for all five-section 2630 Series Disks.
With this feature, a large spring is placed in the wing frame on each side of the disk. As the pivot point in the wing starts to raise, the spring presses against that point to keep the disk level through tough field conditions.
The red circles below illustrate the area of the disk where the large spring is placed in the wing frame.
Mechanical wing control
John Deere’s mechanical wing control is an industry-exclusive feature. A five-section disk without mechanical wing control can show up to 75-mm (3-in.) of depth inconsistency across the wing frame.
185-mm (7.25-in.) and 230-mm (9-in.) blade spacing available for 2630 Disk
The 2630 General-Purpose Disk comes equipped with front and rear solid-spherical disk blades with 185-mm (7.25-in.) or 230-mm (9-in.) spacing. The primary blade size is 560 mm (22 in.) x 4.5 mm (0.177 in.)
Available blade options for the 2630 are listed below.
185-mm (7.25-in.) blade spacing
230-mm (9-in.) blade spacing
185-mm (7.25-in.) spacing, front and rear
- Ideal for seedbed preparation and chemical incorporation
- Provides limited residue-handling capability
- Works best in light to medium soils
230-mm (9-in.) spacing, front and rear
- Good for seedbed preparation and chemical incorporation in medium to heavy soils
- Works well in primary tillage in light to medium soils
- Provides good residue-handling capability
NOTE:
- The number 1 edge has a beefier profile and is best for rocky conditions.
- The number 10 edge has a narrower profile and should work well in most non-rock conditions.
- Rear main and wing gangs are tapered with one blade 51 mm (2 in.) smaller than the primary blade.
- Integral furrow filler blades are included with all rear wing gangs which are 102 mm (4 in.) smaller than the primary blade.
- Front outer gangs have a taper that is 51 mm (2 in.) smaller than the primary blade, except for 559-mm (22-in.) disk blades.
Number 1 edge (outside bevel, outside grind)
Number 10 edge (inside bevel, outside grind)
- Bevel
- Grind
Extended-life bearings improve productivity
John Deere’s 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil types.
The flange-mounted bearing and sealing system features improved contamination resistance. The advanced seal material is highly resistant to wear and damage caused by abrasive soils and other crop materials. The design of these are more durable and reliable than previous bearings.
The design of this bearing system allows for dynamic self-alignment to the gang bolt, as opposed to trunnion-mounted bearings that have limited alignment capability. This system features additional freedom of movement, accommodating a wider variety of field conditions. The bearing system has been designed to decrease stress and fatigue on the inner rolling surfaces, supporting extended bearing life.
The bearing and seal design allows for a limited, seasonal maintenance interval to minimize downtime. They also allow producers to customize the maintenance for specific growing conditions and soil types. The multi-lipped sealing system cannot be damaged by frequent greasing. It allows bearings to accept grease within the bearing as well as provide grease to the outer bearing surface to eliminate wear between the bearing and housing. With this design, the bearings can accept grease even if misaligned to the housing.
2630 Series includes disks for light, medium, and heavy-duty tillage
Ground-engaging components on 2633
Ground-engaging components on 2633
The John Deere 2630 Series offer three disk models that provide a wide range of variety for all tillage applications.
Model |
2630 Disk | 2633 Disk | 2635 Disk |
| Purpose | Secondary (light duty) | Dual purpose (medium duty) | Primary (heavy duty) |
| Working depth | Up to 130 mm (5 in.) | Up to 180 mm (7 in.) | Up to 200 mm (8 in.) |
| Weight per blade | Minimum 68 kg (150 lb) | Under 13.4 m (44 ft) Minimum 86 kg (190 lb) Over 13.4 m (44 ft) Minimum 91 kg (200 lb) |
Minimum 127 kg (280 lb) |
| Blade size | 560 or 610 mm (22 in. or 24 in.) |
610 or 660 mm (24 in. or 26 in.) |
610 or 660 mm (24 in. or 26 in.) |
| Blade spacing | 185 or 230 mm (7.25 in. or 9 in.) |
230 mm (9 in.) | 230 mm (9 in.) (front) and 280 mm (11 in.) (rear), or 280 mm (11 in.) |
| Horsepower | 23 - 36 hp/m (7 - 11 hp/ft) | 23 - 36 hp/m (7 - 11 hp/ft) | 26 - 36 hp/m (8 - 11 hp/ft) |
| Working widths | 6.3 m - 15.0 m (20.75 ft - 49.25 ft) |
6.3 m - 15.0 m (20.75 ft - 49.25 ft) |
7.2 m-12.4 m (23.58 - 40.66 ft) |
| Operating speed | 6.5 - 11.3 km/h (4 - 7 mph) |
6.5 - 11.3 km/h (4 - 7 mph) |
6.5 - 11.3 km/h (4 - 7 mph) |
| Recommended use |
|
|
|
Variety of residue managing solutions available
Residue management
As crop yields increase, so does the amount of residue after harvest. The John Deere 2630 Disk enables producers to prepare soil for planting.
Utilize the residue calculator to identify the optimal residue management solution to meet the producer’s needs.
Multiple enhancements made to 2630 Series Disks
The 2630 Series Disks offer multiple upgrades and new items as options versus the 2620 Series Disks to enhance the machine. Check out the following video sharing more about the new 2630 Series Disks.
Extended-life bearings
John Deere’s 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil type.
TruSet™ side-to-side feature
John Deere TruSet system is featured in base equipment for the 2630 Series Disks and Vertical Tillage Implements. TruSet side-to-side is also available and features individual section leveling.
Knife-edge hydraulic rolling basket
The hydraulic rolling basket is now offered with a round bar, flat bar, or knife-edge. The knife-edge is best for heavier, wet soil, and can be used in rocky conditions.
Radial tires
The 2630 Series Disks and Vertical Tillage Implements feature radial tires for the mainframes in base equipment. Radial tires are available as an option on the wing frame and stabilizer wheels. These tires are designed to offer longer wear life and help minimize compaction with a wider plate and lower inflation pressures.
Stabilizer wheels
Producers can choose either mechanical stabilizer wheels or TruSet hydraulic stabilizer wheels as an option. Stabilizer wheels help to maintain a consistent, level depth and are recommended for operation on rolling ground. The mechanical stabilizer wheels can be manually adjusted with a turnbuckle. TruSet with side-to-side leveling capabilities also enables operators to control the TruSet hydraulic stabilizer wheels from the cab while on the go.
Easily tension disk gang bolts
51-mm (2-in.) disk gang bolts
Gang tension system
John Deere's 2630 Series Disks provide an innovative approach to tension disk gang bolts.
Different blade options for soil penetration and residue sizing
John Deere's 2630 Series Disks offer different blade options for soil penetration and residue sizing.
Solid-spherical blade
Cutout-spherical blade
| Blade type | Solid-spherical blades | Cutout-spherical blades |
| Recommended application |
|
|
| Recommended soil type | Light to medium soils | Heavy to medium soils |
| Benefits | Better control of soil than cone blades since less sensitive to over speeding | Chopping or trapping residue |
| Penetration | Penetrate best at a 20-degree gang angle | Penetration is excellent with a cutout blade |
Disk blade options
- Disk blades compatible with 2630 Disk
- Disk blades compatible with 2633 Disk
- Disk blades compatible with 2635 Disk
Hydraulic fore-aft leveling enables operators to level disks from tractor cab
Hydraulic fore-aft leveling
Hydraulic fore-aft leveling comes as standard equipment with John Deere's 2630 Series Disks. Operators can level the disk from the comfort of the tractor cab.
Features
- Residue Conditions: light/medium
- Depth Control: TruSet/Single-point
- Working Depth: up to 5 in (127 mm)
- Required HP (Engine)/FT: 7 to 11 (17.15-26.95 kw/m)
- Working Speed: 5 to 7 mph (8-11.3 km/h)
- Weight /blade: 179 lbs to 209 lbs (81.2-94.8 kg)
Copy Set
Mechanical wing control increases frame levelness for five-section disks
Spring pack
Spring pack
John Deere’s mechanical wing control helps producers keep their frames level for five-section disks. Mechanical wing control is included in base equipment for all five-section 2630 Series Disks.
With this feature, a large spring is placed in the wing frame on each side of the disk. As the pivot point in the wing starts to raise, the spring presses against that point to keep the disk level through tough field conditions.
The red circles below illustrate the area of the disk where the large spring is placed in the wing frame.
Mechanical wing control
John Deere’s mechanical wing control is an industry-exclusive feature. A five-section disk without mechanical wing control can show up to 75-mm (3-in.) of depth inconsistency across the wing frame.
185-mm (7.25-in.) and 230-mm (9-in.) blade spacing available for 2630 Disk
The 2630 General-Purpose Disk comes equipped with front and rear solid-spherical disk blades with 185-mm (7.25-in.) or 230-mm (9-in.) spacing. The primary blade size is 560 mm (22 in.) x 4.5 mm (0.177 in.)
Available blade options for the 2630 are listed below.
185-mm (7.25-in.) blade spacing
230-mm (9-in.) blade spacing
185-mm (7.25-in.) spacing, front and rear
- Ideal for seedbed preparation and chemical incorporation
- Provides limited residue-handling capability
- Works best in light to medium soils
230-mm (9-in.) spacing, front and rear
- Good for seedbed preparation and chemical incorporation in medium to heavy soils
- Works well in primary tillage in light to medium soils
- Provides good residue-handling capability
NOTE:
- The number 1 edge has a beefier profile and is best for rocky conditions.
- The number 10 edge has a narrower profile and should work well in most non-rock conditions.
- Rear main and wing gangs are tapered with one blade 51 mm (2 in.) smaller than the primary blade.
- Integral furrow filler blades are included with all rear wing gangs which are 102 mm (4 in.) smaller than the primary blade.
- Front outer gangs have a taper that is 51 mm (2 in.) smaller than the primary blade, except for 559-mm (22-in.) disk blades.
Number 1 edge (outside bevel, outside grind)
Number 10 edge (inside bevel, outside grind)
- Bevel
- Grind
Extended-life bearings improve productivity
John Deere’s 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil types.
The flange-mounted bearing and sealing system features improved contamination resistance. The advanced seal material is highly resistant to wear and damage caused by abrasive soils and other crop materials. The design of these are more durable and reliable than previous bearings.
The design of this bearing system allows for dynamic self-alignment to the gang bolt, as opposed to trunnion-mounted bearings that have limited alignment capability. This system features additional freedom of movement, accommodating a wider variety of field conditions. The bearing system has been designed to decrease stress and fatigue on the inner rolling surfaces, supporting extended bearing life.
The bearing and seal design allows for a limited, seasonal maintenance interval to minimize downtime. They also allow producers to customize the maintenance for specific growing conditions and soil types. The multi-lipped sealing system cannot be damaged by frequent greasing. It allows bearings to accept grease within the bearing as well as provide grease to the outer bearing surface to eliminate wear between the bearing and housing. With this design, the bearings can accept grease even if misaligned to the housing.
2630 Series includes disks for light, medium, and heavy-duty tillage
Ground-engaging components on 2633
Ground-engaging components on 2633
The John Deere 2630 Series offer three disk models that provide a wide range of variety for all tillage applications.
Model |
2630 Disk | 2633 Disk | 2635 Disk |
| Purpose | Secondary (light duty) | Dual purpose (medium duty) | Primary (heavy duty) |
| Working depth | Up to 130 mm (5 in.) | Up to 180 mm (7 in.) | Up to 200 mm (8 in.) |
| Weight per blade | Minimum 68 kg (150 lb) | Under 13.4 m (44 ft) Minimum 86 kg (190 lb) Over 13.4 m (44 ft) Minimum 91 kg (200 lb) |
Minimum 127 kg (280 lb) |
| Blade size | 560 or 610 mm (22 in. or 24 in.) |
610 or 660 mm (24 in. or 26 in.) |
610 or 660 mm (24 in. or 26 in.) |
| Blade spacing | 185 or 230 mm (7.25 in. or 9 in.) |
230 mm (9 in.) | 230 mm (9 in.) (front) and 280 mm (11 in.) (rear), or 280 mm (11 in.) |
| Horsepower | 23 - 36 hp/m (7 - 11 hp/ft) | 23 - 36 hp/m (7 - 11 hp/ft) | 26 - 36 hp/m (8 - 11 hp/ft) |
| Working widths | 6.3 m - 15.0 m (20.75 ft - 49.25 ft) |
6.3 m - 15.0 m (20.75 ft - 49.25 ft) |
7.2 m-12.4 m (23.58 - 40.66 ft) |
| Operating speed | 6.5 - 11.3 km/h (4 - 7 mph) |
6.5 - 11.3 km/h (4 - 7 mph) |
6.5 - 11.3 km/h (4 - 7 mph) |
| Recommended use |
|
|
|
Variety of residue managing solutions available
Residue management
As crop yields increase, so does the amount of residue after harvest. The John Deere 2630 Disk enables producers to prepare soil for planting.
Utilize the residue calculator to identify the optimal residue management solution to meet the producer’s needs.
Multiple enhancements made to 2630 Series Disks
The 2630 Series Disks offer multiple upgrades and new items as options versus the 2620 Series Disks to enhance the machine. Check out the following video sharing more about the new 2630 Series Disks.
Extended-life bearings
John Deere’s 2630 Series Disks and Vertical Tillage Implements feature extended-life bearings. These more durable and reliable bearings allow producers to customize bearing maintenance for specific growing conditions and soil type.
TruSet™ side-to-side feature
John Deere TruSet system is featured in base equipment for the 2630 Series Disks and Vertical Tillage Implements. TruSet side-to-side is also available and features individual section leveling.
Knife-edge hydraulic rolling basket
The hydraulic rolling basket is now offered with a round bar, flat bar, or knife-edge. The knife-edge is best for heavier, wet soil, and can be used in rocky conditions.
Radial tires
The 2630 Series Disks and Vertical Tillage Implements feature radial tires for the mainframes in base equipment. Radial tires are available as an option on the wing frame and stabilizer wheels. These tires are designed to offer longer wear life and help minimize compaction with a wider plate and lower inflation pressures.
Stabilizer wheels
Producers can choose either mechanical stabilizer wheels or TruSet hydraulic stabilizer wheels as an option. Stabilizer wheels help to maintain a consistent, level depth and are recommended for operation on rolling ground. The mechanical stabilizer wheels can be manually adjusted with a turnbuckle. TruSet with side-to-side leveling capabilities also enables operators to control the TruSet hydraulic stabilizer wheels from the cab while on the go.
Easily tension disk gang bolts
51-mm (2-in.) disk gang bolts
Gang tension system
John Deere's 2630 Series Disks provide an innovative approach to tension disk gang bolts.
Different blade options for soil penetration and residue sizing
John Deere's 2630 Series Disks offer different blade options for soil penetration and residue sizing.
Solid-spherical blade
Cutout-spherical blade
| Blade type | Solid-spherical blades | Cutout-spherical blades |
| Recommended application |
|
|
| Recommended soil type | Light to medium soils | Heavy to medium soils |
| Benefits | Better control of soil than cone blades since less sensitive to over speeding | Chopping or trapping residue |
| Penetration | Penetrate best at a 20-degree gang angle | Penetration is excellent with a cutout blade |
Disk blade options
Hydraulic fore-aft leveling enables operators to level disks from tractor cab
Hydraulic fore-aft leveling
Hydraulic fore-aft leveling comes as standard equipment with John Deere's 2630 Series Disks. Operators can level the disk from the comfort of the tractor cab.